|
Post by schmooot on May 8, 2005 12:14:01 GMT -5
|
|
|
Post by schmooot on May 8, 2005 12:18:45 GMT -5
Schmoot ~ your car is really tricked out. Tell us those photo shots are a before and after. Did you weld new sheet metal to the rusted areas or did you use gallons of bondo? Wow. Im speechless. How does your short ram work? :-Xtricked riiiight. Actually I was sans welder at the time so I played a little with the fiberglass matting and some creative mold procedures. Then with the long strand fiberglass to fill, then the bondo. I'm quite happy with how the shapes came back to life. And yes the first shots are before I sandblasted and cut and grinded and such, and the second set are after many weeks of work on and off I just got my hours cut at work down to 20 a week so I'll have lots of time to mess around and get er done
|
|
|
Post by schmooot on May 8, 2005 12:23:44 GMT -5
quick question guys. It's been a while since I pulled these side spoiler pieces off my parts car and I borke them when I did it so I can't remember what it entitles. There are a couple screws visible on the inside, so I pull those out and are there clips (so I can slide the piece off them) or bolts (do I have to pull out the interior panel to get at the inside/backside of them to remove)? I want to take them off to paint them but don't want to break the clips on the inside.
|
|
|
Post by White87GT on May 8, 2005 16:10:35 GMT -5
Schmoot - There should be 3 screws on each side of the wing ends. Remove these (the middle one is a long one) and then the thing should lift right up.
|
|
|
Post by schmooot on May 10, 2005 12:51:22 GMT -5
Schmoot - There should be 3 screws on each side of the wing ends. Remove these (the middle one is a long one) and then the thing should lift right up. up? not out or back or forward right?
|
|
|
Post by buzzbomber87gts on May 10, 2005 13:07:18 GMT -5
should lift up
|
|
|
Post by White87GT on May 10, 2005 22:38:41 GMT -5
up? not out or back or forward right? Should be up.
|
|
|
Post by schmooot on May 12, 2005 8:40:21 GMT -5
right on
|
|
ERock
New Member
Posts: 9
|
Post by ERock on May 15, 2005 9:15:41 GMT -5
Dude, finally someone in the same perdicament as me, my 89 ST is also rusted out pretty bad, not as bad as yours was but there are holes in my rear quarter panel wich allows water from the tires to blow up into the trunk. me and my dad are about to start sandblasting in a couple of weeks when schools out i hope, if there are any helpfull tips u could give me, it would be Greatly appreciated, Thx
|
|
ERock
New Member
Posts: 9
|
Post by ERock on May 15, 2005 9:18:41 GMT -5
Also, did u buy that hood scoop? if so how much did u pay for it? and was it hard to install?
|
|
|
Post by schmooot on May 23, 2005 2:39:26 GMT -5
|
|
|
Post by schmooot on May 23, 2005 2:40:53 GMT -5
Also, did u buy that hood scoop? if so how much did u pay for it? and was it hard to install? made it from scratch
|
|
|
Post by 4thgenceli on May 23, 2005 10:04:56 GMT -5
Damn, good work man. You wanna come and help me paint my car??
|
|
|
Post by schmooot on May 23, 2005 12:33:26 GMT -5
Damn, good work man. You wanna come and help me paint my car?? Only if there is no bodywork involved whatsoever. damn I hate bodywork
|
|
|
Post by 4thgenceli on May 23, 2005 13:15:46 GMT -5
Only the Driver quarter panel is a little dinged up. other than that. perfect.
Aren't you in CA?
|
|